ผลิตภัณฑ์ทั้งหมด
  • HUATEC GROUP CORPORATION
    บ๊อบ
    Astm E114-15 Inch Type 1018 Calibration Test Block เหล็กกล้าคาร์บอน Mini Iiw 2
  • HUATEC GROUP CORPORATION
    วิลเลี่ยม
    Astm E114-15 Inch Type 1018 Calibration Test Block เหล็กกล้าคาร์บอน Mini Iiw 2
  • HUATEC GROUP CORPORATION
    ทอม
    Astm E114-15 Inch Type 1018 Calibration Test Block เหล็กกล้าคาร์บอน Mini Iiw 2
  • HUATEC GROUP CORPORATION
    สิงห์
    Astm E114-15 Inch Type 1018 Calibration Test Block เหล็กกล้าคาร์บอน Mini Iiw 2
ชื่อผู้ติดต่อ : Noah
หมายเลขโทรศัพท์ : +8613911115555
วอทส์แอพพ์ : +8613910983110

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE

สถานที่กำเนิด ปักกิ่ง
ชื่อแบรนด์ HUATEC
ได้รับการรับรอง ISO, CE, GOST
หมายเลขรุ่น เอชเอฟดี ยูแอล
จำนวนสั่งซื้อขั้นต่ำ 1PCS
รายละเอียดการบรรจุ แพ็คเกจส่งออกมาตรฐาน
เวลาการส่งมอบ 1-4 วัน
เงื่อนไขการชำระเงิน T/T PayPal เวสเทิร์นยูเนี่ยน
สามารถในการผลิต 5,000 ชิ้นต่อเดือน

ติดต่อฉันเพื่อตัวอย่างฟรีและคูปอง

วอทส์แอพพ์:0086 18588475571

วีชัต: 0086 18588475571

สกายเป้: sales10@aixton.com

หากคุณมีปัญหา เราให้ความช่วยเหลือออนไลน์ตลอด 24 ชั่วโมง

x
รายละเอียดสินค้า
ช่วงความถี่ 12.5KHz ถึง 10MKHz ทรานสดิวเซอร์แบบสัมผัส ขนาดองค์ประกอบต่างๆ
ตัวแปลงสัญญาณใบหน้าที่ได้รับการปกป้อง ด้วยฟิล์มหรือรองเท้า เครื่องปรับเปลี่ยนสรรพธาตุคู่ องค์ประกอบคู่
ลิ่มทรงโค้ง เอด ซีไอดี เอโอดี ซีโอดี วัสดุ พลาสติก, อลูมิเนียม, โลหะผสม
เน้น

ultrasonic flaw detectors

,

ultrasonic flaw detection

,

digital ultrasonic flaw detector

ฝากข้อความ
รายละเอียดสินค้า

 

Ultrasonic ndt equipment Ultrasonic Inspection Equipment Probe Transducer Phased Array Prob

 

1. Straight probe: single crystal p-wave straight probe double crystal p-wave straight probe

 

2. The Angle probe: single crystal shear Angle probe a1 < aL < a Ⅱ, twin shear Angle probe

 

Single-crystal p-wave oblique probe aL

AL is a climbing wave probe near a1. The longitudinal wave transmitted along the surface of the workpiece has the advantages of fast speed, high energy, long wavelength, deeper detection depth than the surface wave, and the requirement for the surface finish of the workpiece is higher than that of the surface wave (frequency 2.5mhz wavelength about 2.4mm).

 

3. Probe with curvature: circumferential curvature, radial curvature.

 

The circumferential curvature probe is suitable for the detection of axial defects in seamless steel tubes, straight welded tubes, tubular forgings and axial workpieces. When the diameter of the workpiece is less than 2000mm, the circumferential curvature of the probe shall be ground to ensure good coupling.

 

Radial curvature probe is suitable for the detection of radial defects in seamless steel pipe, butt weld of steel pipe, barrel forging, shaft workpiece, etc. When the workpiece diameter is less than 600mm, the radial curvature of the probe should be ground to ensure good coupling.

 

4. Focusing probe: point focusing line focusing.

 

5. Surface wave probe :(when the incident Angle of the longitudinal wave is greater than or equal to the second critical Angle, the transverse wave refraction Angle is equal to 90 to form a surface wave).

 

The transverse wave transmitted along the workpiece surface has a slow speed, low energy and short wavelength, and the detection depth is shallower than the crawling wave. Therefore, the requirements for the surface finish of the workpiece are stricter than the crawling wave.

 

Surface wave detection can only detect defects at a depth of two wavelengths from the surface of the workpiece. (frequency 2.5mhz wavelength about 1.3mm).

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 0

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 1

 

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 2

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 3

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 4

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 5

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 6

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 7

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 8

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 9Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 10

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 11

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 12

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 13

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 14

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 15

แนะนำผลิตภัณฑ์